Battman Digital Dashboard Display

Battman Digital Dashboard Display
Battman Digital Dashboard Display Battman Digital Dashboard Display Battman Digital Dashboard Display Battman Digital Dashboard Display Battman Digital Dashboard Display
Product Code: Batt-Man
Availability: In Stock
Price: $93.00
Ex Tax: $93.00

2 or more $92.50
5 or more $91.00
10 or more $90.00
25 or more $89.00
50 or more $88.00
100 or more $87.00

Available Options


System Voltage:

* High Current Version:

Qty:     - OR -   Add to Wish List
Add to Compare

Batt-man digital dashboard

software link 

user manual link

(troubleshooting added to manual)

 

Advantages:
* easy installation can be hooked to every system without any modifications/ adjusments
* very accurate
* pc interface (GUI - Graphical User Interface) - connect with any simple mini USB no drivers needed.
* real waterproof
* give you data about your ride/ use 
* two vesrsions - rear and front as to your motor position
* very good display , very good contrast even on direct sunlight
* we can adjust the main wire and speed sensor as to costumer request
* we ca offer the same contactor as on your current system
 

Batt-man is the ultimate gadget for the connoisseur electric rider. It provides a wide variety of accurate information about the battery and vehicle performance. Click on the image bellow to view Batt-mans 3 screens.

 

 SPECIFICATIONS 
 

Maximum continuous current - 70A

Maximum momentary current - 160A (for less than 5 seconds)

Maximum voltage - 100V we can offer vesion for over 100V ( the minimum voltage require to start the display will be 40V)

Start UP voltage: 8V / vesion for over 100V ( the minimum voltage require to start the display will be 40V)

Maximum amp hour - 65.000Ah

Maximum watt hour - 6500.0Wh

Blue backlight for night vision

USB interface

Batt-man digital dashboard has 3 screens:

 

Main screen

Speedometer- displays speed in the desired measurement units (km/h, mph).

Trip odometer- displays driving distance since it was last reset.

Graphical fuel gauge- a visual way to indicate how much battery power is left.

 

Battery meter screen

Current- displays the instantaneous Amperes flowing in the system.

Voltage- displays battery voltage.

Discharge- displays the accumulated Amp-hours drawn since it was last reset.

Power- displays the instantaneous power of the system. (* when there is no current this field shows Wh).

 

Peak data screen

Max Amps- displays the maximum recorded Amps.

Min Voltage- displays the minimum measured battery voltage.

Top speed- displays the maximum recorded speed.

Max Watts- displays the maximum recorded power.

 

Batt-man digital dashboard GUI(Graphical User Interface):

Batt-man digital dashbord has a USB interface, for easy setup, logging uploads and firmware updade. 
 
include 3 screens : 

Settings screen, Logger screen, Advanced screen)

 

Totals:

"Read total" - reads the accumulated values stored in Batt-man's internal flash.

"Reset" - resets the accumulated values stored in Batt-man's internal flash, use it when replacing a battery or installing the Batt-man on a new vehicle.

 

Setup:

"Program" - sends the values selected to Batt-man's memory

"Read" - Reads current settings from Batt-man's memory (called automatically when connected)

"Wheel diameter" - set your wheel diameter or circumference, for the speedometer.

"Battery capacity" - set your total battery capacity (XX.XXXAh). Batt-man will use this setting to calculate the amount of charge left in the battery.

Upgrade:

"Upgrade firmware" - use this button to change Batt-man's firmware, when new firmware is available.

Calibration:

"Program" - sends the values selected to Batt-man's memory

"Read" - Reads current settings from Batt-man's memory (called automatically when connected)

"load defaults" - every Batt-man is manually calibrated, these default calibration settings can always be retrieved.

"Shunt resistance" - the value in milliohms of your shunt.(*)

"Shunt offset" - if your Amps reading is not 0 when there is no load, add the Amps reading to this value in order to reach 0 reading.(*)

"Voltage divider" - used to calibrate the voltage.(*)

"Voltage offset" - used to calibrate the voltage.(*)

* Advanced users use only.

Write a review

Your Name:


Your Review: Note: HTML is not translated!

Rating: Bad           Good

Enter the code in the box below:




Powered By OpenCart
Green Motion © 2017